Monday, November 18, 2013
Copy Paste SETUP and BIND
My setup is as follows.
Park 370 outrunner motor
APC 8 X 3.8 SF Propeller
12 amp brushless ESC
Thunder Power 3 Cell 730 mAh 11.1v Battery
2 E-Flite S-60 servos
Futaba R606FS Receiver
Futaba 2.4 Ghz Fasst Controller
Specification:
Wingspan: 610mm
Length: 415mm
Flying wight: 175g (6.2oz)
Drive System: 1822/2600KV brushless outrunner motor
Speed Controller: 6A brushless ESC
Servo: 8g X1;5g X2 speed micro servos
Battery: High Quality Rechargeable 7.4V 500mAh 15C Li-Po Battery
Motor: Brushless 1822/2600KV
Control system: 4 CH 2.4GHz Multifunctional Transmitter and Receiver
Radio Control Range: 900 feet (300m)
Here is what is on the manual.
Before using K-7XII, you must bind the transmitter and the receiver. Binding them as following
steps:
1)Plug the 'BIND line' into the 'BIND' slot of receiver. Then power on receiver by plugging the
ESC line, then the LED of receiver will flash fast. Then you can remove the 'BIND line'.
2)Hold 'ESC' button of transmitter, then turn on it (keep holding), the LCD will display as
following.
3)After few seconds, binding will finish, the LED of receiver will shine three times slowly, and
then the transmitter enters working mode.
4)Release 'ESC' button of transmitter, it will enter working mode.
Notice:
1)K-7XII supports multiple receivers operation and long-distance binding, so please make sure
only you bind the radio at that time. If there is any person who also uses KDS-7XII 2.4GHz
remote controller system locally, please operates only after other users pare the signal.
2)K-7XII supports seven models saving in one transmitter. They are numbering as M/1 to M/7.
The binding will save the serial numbers in receiver. So if you bind one receiver with M/1, it
can only work when the transmitter is switched to M/1.
I have also found that when you bind it is best to be about three feet away from the receiver.
Just trying to help
Park 370 outrunner motor
APC 8 X 3.8 SF Propeller
12 amp brushless ESC
Thunder Power 3 Cell 730 mAh 11.1v Battery
2 E-Flite S-60 servos
Futaba R606FS Receiver
Futaba 2.4 Ghz Fasst Controller
Specification:
Wingspan: 610mm
Length: 415mm
Flying wight: 175g (6.2oz)
Drive System: 1822/2600KV brushless outrunner motor
Speed Controller: 6A brushless ESC
Servo: 8g X1;5g X2 speed micro servos
Battery: High Quality Rechargeable 7.4V 500mAh 15C Li-Po Battery
Motor: Brushless 1822/2600KV
Control system: 4 CH 2.4GHz Multifunctional Transmitter and Receiver
Radio Control Range: 900 feet (300m)
Here is what is on the manual.
Before using K-7XII, you must bind the transmitter and the receiver. Binding them as following
steps:
1)Plug the 'BIND line' into the 'BIND' slot of receiver. Then power on receiver by plugging the
ESC line, then the LED of receiver will flash fast. Then you can remove the 'BIND line'.
2)Hold 'ESC' button of transmitter, then turn on it (keep holding), the LCD will display as
following.
3)After few seconds, binding will finish, the LED of receiver will shine three times slowly, and
then the transmitter enters working mode.
4)Release 'ESC' button of transmitter, it will enter working mode.
Notice:
1)K-7XII supports multiple receivers operation and long-distance binding, so please make sure
only you bind the radio at that time. If there is any person who also uses KDS-7XII 2.4GHz
remote controller system locally, please operates only after other users pare the signal.
2)K-7XII supports seven models saving in one transmitter. They are numbering as M/1 to M/7.
The binding will save the serial numbers in receiver. So if you bind one receiver with M/1, it
can only work when the transmitter is switched to M/1.
I have also found that when you bind it is best to be about three feet away from the receiver.
Just trying to help
Subscribe to:
Posts (Atom)